LCD module data
Numeric
Character
Mixed
- ≡ Uniden FP203 ✘
- ≡ Uniden FP204 ✘
- ≡ VIP89Z G-Code ✘
Graphic
key: ≡ parallel, ↔ serial, ~ LVDS, _ unknown, ✘ discarded as not useful
Resources
This is an old revision of the document!
LCD Description |
|
|---|---|
| Model | MDP12BS17-SR-T |
| Manufacturer | |
| Recovered from | Epson WF-2530 1) |
| Board IDs | 2142717-01, 2142716 00 |
| LCD type | positive |
| Polarizer type | reflective |
| Columns | 126 (128?) pixels 2) |
| Rows | 26 (32?) pixels |
| Char matrix | - |
| Driver IC | (CoG) |
| Backlight | - |
| Arduino driver | |
| Connector | pins |
| Num Pins | 8 |
| Pin spacing | 0.07“ |
| LCD1 Pinout | Arduino test rig 3) | ||||
|---|---|---|---|---|---|
| Pin# | Label | Connected to | Measured | Pin | colour |
| 1 | CS | (cn1 pin 8) | 3.38V | ||
| 2 | ? | (74VHC595 pin 4 (Qe)) | 3.38V | ||
| 3 | Keypressed Data? | (cn1 pin6, 74VHC595 pin 14 (SER data input) via 100Ω) | 0V | ||
| 4 | CLK | (cn1 pin5 via 220Ω), (74VHC595 pin 11 (clock) via 220Ω), (74VHC165 pin 2 (clock) via 220Ω) 250kHz or 3MHz | 0V | ||
| 5 | DATA IN | (cn1 pin2), (74VHC165 pin 9 (QH) via 3.3k) | 3.38V | ||
| 6 | Vcc | 3.38V | |||
| 7 | GND | oV | |||
| 8 | VLCD | capacitor to GND | 6.94V | ||
| JK33149A, 2142717-01 Board, CN1 pinout | Arduino test rig 4) | |||
|---|---|---|---|---|
| Pin# | Label | Connected to | Pin | colour |
| 1 | Buzzer- | |||
| 2 | (lcd pin5) | |||
| 3 | GND | |||
| 4 | Vcc? | |||
| 5 | CLK? | (lcd pin4 via 220Ω), (74VHC595 pin 11 (clock) via 220Ω), (74VHC165 pin 2 (clock) via 220Ω) | ||
| 6 | (lcd pin3 via 100Ω) | |||
| 7 | (74VHC595 pin 13 (output enable)) | |||
| 8 | (lcd pin1) | |||
| 9 | (74VHC165 pin 1 (parallel load)) | |||
| 10 | SW1 (closes to gnd) (power button) | |||
“2 line bitmap LCD” Approximately 20 characters by 2 rows.
IC1, 74VHC165 (8bit parallel line/serial out shift register) is used for serializing the keyswitch selections,
IC2. 74VHC595 (8-Bit Shift Register with Output Latches) is used for decoding serial data to latched outputs to turn on status LEDs (Power, Wifi, ADF) and one LCD control line (chip select?)
IC1 & IC2 can use power supplies of 2V to 5.5V, so LCD maybe 3.3V?
Examples :
electronic/lcd/mdp12bs17srt.1540874040.txt.gz · Last modified: 2018/10/30 04:34 by tony
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International