LCD module data
Numeric
Character
Mixed
- ≡ Uniden FP203 ✘
- ≡ Uniden FP204 ✘
- ≡ VIP89Z G-Code ✘
Graphic
key: ≡ parallel, ↔ serial, ~ LVDS, _ unknown, ✘ discarded as not useful
Resources
This is an old revision of the document!
| LCD Description | |
|---|---|
| Model | LMCCAT299C |
| Manufacturer | NAN YA Plastics Corp (Taiwan) |
| Recovered from | Wayfarer TGX 13722 1) |
| Board IDs | M299- Rev.A, D36072B1J, M299-GA, 36171103M336, LMCCAT299C |
| LCD type | positive |
| Polarizer type | transflective |
| Columns | 192 pixels |
| Rows | 128 pixels |
| Char matrix | 6×8 |
| Driver IC | T6963C |
| Backlight | yellow-green |
| Arduino driver | U8g2lib.h |
| Connector | pin header |
| Num Pins | 20 |
| Pin spacing | 0.1“ |
| Module size | mm |
| Connector pin-out 2) | |||
|---|---|---|---|
| Pin# | IC pin | Label | Description |
| 1 | FG | Frame Ground | |
| 2 | 63 | VSS | Ground |
| 3 | 61 | VDD | Supply Voltage for Logic |
| 4 | VO | (variable) Supply Voltage for LCD | |
| 5 | VEE | Negative Voltage Output | |
| 6 | 18 | /WR | Data Write |
| 7 | 19 | /RD | Data Read |
| 8 | 20 | /CE | Chip Enable |
| 9 | 21 | C/D | Command Write |
| 10 | 1 | /HALT | Clock Operating Stop Signal |
| 11 | 2 | /RESET | Reset Signal |
| 12 | 10 | DB0 | Data Bus Line 0 |
| 13 | 11 | DB1 | Data Bus Line 1 |
| 14 | 12 | DB2 | Data Bus Line 2 |
| 15 | 13 | DB3 | Data Bus Line 3 |
| 16 | 14 | DB4 | Data Bus Line 4 |
| 17 | 15 | DB5 | Data Bus Line 5 |
| 18 | 16 | DB6 | Data Bus Line 6 |
| 19 | 17 | DB7 | Data Bus Line 7 |
| 20 | NC | No Connection | |
From a photo of the T6963C pins 3,6,7,9 are tied together, it is not apparent whether they go to Vdd or Vss. If it is Vss then maximum vertical resolution would be 64 v-dots, which seems a bit small for a 95mm high display, so I'll assume they're all tied to Vdd.
| Display size selectors (hard wired) | |||
|---|---|---|---|
| Pin# | IC pin | Wired | Value |
| Dual | 54 | 1 | |
| MDS | 3 | 1 | |
| MD0 | 4 | 0 | |
| MD1 | 5 | 0 | |
⇒ 80 to 128 vertical dots, from the physical size most likely 128 (16 lines of characters).
128 is now confirmed from looking at a sample of these displays.
| Display size selectors (hard wired) | |||
|---|---|---|---|
| Pin# | IC pin | Value | |
| MD2 | 6 | 1 | |
| MD3 | 7 | 1 | |
=32 character columns (or this would give 80 columns if they're tied low, a bit excessive for this width display and not enough control chips to handle it).
32 is now confirmed from looking at a sample of these displays.
| Display font size selectors | |||
|---|---|---|---|
| Pin# | IC pin | Value | |
| FS0 | 8 | 0 | |
| FS1 | 9 | 1 | |
not sure what FS0 connects to, if Vdd then 5×8 font ⇒ 160 horizontal dots, if Vss then 6×8 font ⇒192 horizontal dots (but again not enough control chips to handle it).
FS0 apparently does connect to Vss, from looking at a sample of these displays. So this guess was wrong, it is 192 dots wide.
Additional info
- Chips on board: T6963C, T6A39A (x2) T6A40 (x2) , 74HC40103D, 74HC74D, BA10324AF, MT62C256F-70LL
- Similar to OCM160128-1
Examples :
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International