LCD module data
Numeric
Character
Mixed
- ≡ Uniden FP203 ✘
- ≡ Uniden FP204 ✘
- ≡ VIP89Z G-Code ✘
Graphic
key: ≡ parallel, ↔ serial, ~ LVDS, _ unknown, ✘ discarded as not useful
Resources
This is an old revision of the document!
| LCD Description | |
|---|---|
| Model | M299 |
| Manufacturer | NAN YA Plastics Corp (Taiwan) |
| Recovered from | Wayfarer TGX #13722 1) |
| Board IDs | M299- Rev.A, D36072B1J, M299-GA, 36171103M336, LMCCAT299C |
| LCD type | positive |
| Polarizer type | transflective |
| Columns | 160? 192? |
| Rows | 128? |
| Char matrix | 5×8? or 6×8? |
| Driver IC | T6963C |
| Backlight | |
| Arduino driver | U8g2lib.h |
| Connector | pin header |
| Num Pins | 20 |
| Pin spacing | 0.1“ |
| Module size | mm |
| Connector pin-out2) | ||
|---|---|---|
| Possible pin# | Label | |
| 1 | ||
| 2 | ||
| 3 | ||
| 4 | ||
| 5 | ||
| 6 | HALT | |
| 7 | RST | |
| 8 | RST | |
| 9 | SD0 | |
| 10 | SD1 | |
| 11 | SD2 | |
| 12 | SD3 | |
| 13 | SD4 | |
| 14 | SD5 | |
| 15 | SD6 | |
| 16 | SD7 | |
| 17 | WR | |
| 18 | RD | |
| 19 | CE | |
| 20 | C/D | |
| Connector pin-out 3) | Arduino test rig | |||
|---|---|---|---|---|
| Pin# | IC pin | Label | Pin | colour |
| 1 | FG | Frame Ground | ||
| 2 | VSS | Ground | ||
| 3 | VDD | Supply Voltage for Logic | ||
| 4 | VO | (variable) Supply Voltage for LCD | ||
| 5 | VEE | Negative Voltage Output | ||
| 6 | /WR | Data Write | ||
| 7 | /RD | Data Read | ||
| 8 | /CE | Chip Enable | ||
| 9 | C/D | Command Write | ||
| 10 | /HALT | Clock Operating Stop Signal | ||
| 11 | /RESET | Reset Signal | ||
| 12 | DB0 | Data Bus Line 0 | ||
| 13 | DB0 | Data Bus Line 1 | ||
| 14 | DB0 | Data Bus Line 2 | ||
| 15 | DB0 | Data Bus Line 3 | ||
| 16 | DB0 | Data Bus Line 4 | ||
| 17 | DB0 | Data Bus Line 5 | ||
| 18 | DB0 | Data Bus Line 6 | ||
| 19 | DB0 | Data Bus Line 7 | ||
| 20 | NC | No Connection | ||
From a photo of the T6963C pins 3,6,7,9 are tied together, it is not apparent whether they go to Vdd or Vss. If its Vss then max vertical resolution would be 64 v-dots, which seems a bit small for a 95mm high display, so I'll assume they're all tied to Vdd.
| Display size selectors (hard wired) | |||
|---|---|---|---|
| Pin# | IC pin | Wired | Value |
| Dual | 54 | ||
| MDS | 3 | 1 | |
| MD0 | 4 | ||
| MD1 | 5 | ||
⇒ 80 to 128, from the physical size most likely 16 lines (128 vertical dot resolution)
| Display size selectors (hard wired) | |||
|---|---|---|---|
| Pin# | IC pin | Wired | Value |
| MD2 | 6 | 1 | |
| MD3 | 7 | 1 | |
=32 character columns (or this would give 80 columns if they're tied low, a bit excessive for this width display and not enough control chips to handle it )
| Display font size selectors | |||
|---|---|---|---|
| Pin# | IC pin | Wired | Value |
| FS0 | 8 | ||
| FS1 | 9 | 1 | |
not sure what FS0 connects to, if Vdd then 5×8 font ⇒ 160 horizontal dots, if Vss then 6×8 font ⇒196 horizontal dots.
Additional info
- Chips onboard: T6963C, T6A39A (x2) T6A40 (x2) , 74HC40103D, 74HC74D, BA10324AF, MT62C256F-70LL
- Similar to OCM160128-1
Examples :
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International