My Projects

You are here: start » electronic » boards » xc4492

My Projects

User Tools

Site Tools

You are here: start » electronic » boards » xc4492

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision		Previous revision
electronic:boards:xc4492 [2026/10/12 05:50] – created tonyelectronic:boards:xc4492 [2026/10/20 22:26] (current) – tony
Line 4: Line 4:
 \\ \\
  
-{{ :electronic:boards:.jpg?200|Overview}}+{{ :electronic:boards:pa184372a.jpg?200|Overview}}
 ^  Module Description  || ^  Module Description  ||
-^Model|**XC-4492**| +^Model|**XC4492**| 
-^Manufacturer|Duiotech| +^Manufacturer|Duinotech| 
-^Description|Dual/Stepper Motor Controller Module| +^Description|Dual/Stepper motor controller module| 
-^Other designations|-| +^Other designations|Duinotech L298, TA0052 iduino L298 , Keyes L298, Keyestudio L298N| 
-^Associated modules| | +^Associated modules|-| 
-^Voltage|5V| +^Voltage|3V - 30V| 
-^Current|4A max load|+^Current|4A max total load|
 \\ \\
 ===== Overview ===== ===== Overview =====
Line 20: Line 20:
  
 ==== Components ==== ==== Components ====
 +  * {{:electronic:datasheet:stmicroelectronics:ds_l298.pdf|L298N}}, Dual full-bridge driver
  
 ==== Features ==== ==== Features ====
   * 3V DC - 30 V DC operating voltage   * 3V DC - 30 V DC operating voltage
 +  * 2A peek current per motor channel
   * Back-EMF protection   * Back-EMF protection
   * Over-temperature protection   * Over-temperature protection
-  * On-board 5V regulator can provide power to Arduino etc +  * On-board 5V regulator can also power attached Arduino etc 
-  * Status LEDs+  * Status LEDs (logic power and input status) 
 +  * Provision for current sense resistors
  
 ==== Revisions ==== ==== Revisions ====
 +===== Schematics =====
 +^XC4492 circuit schematic :^
 +{{electronic:boards:xc4492_schem.png?800|Schematic}}
 +
 +Note: C1 not actually installed.
 +
 +\\
 +^  Jumper block  ||
 +^CSB|Insert current sense resistor between pins to measure current on channel B, or short with jumper if not used|
 +^CSA|Insert current sense resistor between pins to measure current on channel A, or short with jumper if not used|
 +^UR1|Jumper to activate pullup on IN4 (not needed for Arduino)|
 +^UR2|Jumper to activate pullup on IN3 (not needed for Arduino)|
 +^UR3|Jumper to activate pullup on IN2 (not needed for Arduino)|
 +^UR4|Jumper to activate pullup on IN1 (not needed for Arduino)|
 +
 +^5V_EN|Jumper to enable +5V power to the board via 5V regulator from VMS supply|
 +
 +If you install jumper "5V_EN" the board can generate +5V from the VMS (motor)  supply using an onboard regulator but only if that VMS supply is less than 16V.   That +5V can be used to power an attached Arduino etc via the pin header.   Otherwise (eg VMS >16V, too high for regulator), the board needs an external +5V supply as well as the VMS supply.
  
 \\ \\
 ---- ----
 +
 ===== Examples ===== ===== Examples =====
-{{electronic:boards:.jpg?800|Overview}}+{{electronic:boards:pa184372a.jpg?800|XC4492 overview}} 
 +{{electronic:boards:pa184371a.jpg?800|XC4492 overview back}} 
 +{{electronic:boards:pa184375a.jpg?800|XC4492 top view}} 
 +{{electronic:boards:pa184376a.jpg?800|XC4492 PCB bottom}}
  
 ====== References and Additional Resources ====== ====== References and Additional Resources ======
 +  * {{https://media.jaycar.co.nz/product/resources/XC4492_datasheetMain_67878.pdf?_gl=1*1q73kcn*_gcl_au*MzA1ODQ3MDUuMTc5MTkzMjE3OQ..|XC4492}} datasheet. /* {{:electronic:boards:xc4492.pdf|XC4492}} datasheet. */
 +  * {{https://www.st.com/resource/en/application_note/an240-applications-of-monolithic-bridge-drivers-stmicroelectronics.pdf|L293, L293E and L298}} application notes.
 +  * {{https://www.auselectronicsdirect.com.au/assets/files/TA0052%20Stepper%20Motor%20Controller%20Module.pdf|TA0052}} datasheet.
 +  * {{https://wiki.keyestudio.com/Ks0063_keyestudio_L298N_Motor_Driver_Board_Module|Keyestudio L298N}} wiki page.
  
 <html><small><p>If any referenced page no longer exists, try looking for its URL on <a href="http://archive.org">http://archive.org</a>.</p></small></html> <html><small><p>If any referenced page no longer exists, try looking for its URL on <a href="http://archive.org">http://archive.org</a>.</p></small></html>

Page Tools

electronic/boards/xc4492.1791784245.txt.gz · Last modified: 2026/10/12 05:50 by tony
CC Attribution-Share Alike 4.0 International Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International