This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| electronic:boards:arduino:duemilanove [2026/10/19 09:24] – [Examples] tony | electronic:boards:arduino:duemilanove [2026/10/22 21:22] (current) – tony | ||
|---|---|---|---|
| Line 5: | Line 5: | ||
| {{ electronic: | {{ electronic: | ||
| ^ Module Description | ^ Module Description | ||
| - | ^Model|**Arduino | + | ^Model|**Duemilanove**| |
| ^Manufacturer|Arduino| | ^Manufacturer|Arduino| | ||
| ^Brand|Arduino| | ^Brand|Arduino| | ||
| ^Clone of|-| | ^Clone of|-| | ||
| - | ^Description|2009 Arduino | + | ^Description|2009 Arduino |
| - | ^Associated modules| | + | |
| ^Voltage|5V| | ^Voltage|5V| | ||
| - | ^Current| | | ||
| ===== Overview ===== | ===== Overview ===== | ||
| - | This Arduino is the predecessor of the Arduino | + | This Arduino is the predecessor of the Arduino |
| + | |||
| + | So in some ways superior to the Uno, it does have a deficit in that the bootloader takes up 2kB vs 0.5kB of the available 32kB of onboard flash ram. It is possible to use an ISP programmer to replace the bootloader code with Optiboot which basically turns it into a Uno with an FTDI USB interface. | ||
| + | |||
| + | Mine was purchased from Jaycar and I don't think it is a genuine original as it doesn' | ||
| - | So in some ways superior to the UNO, it does have a deficit in that the bootloader takes up 2k vs 0.5k of the available 32k of onboard flash ram. It is possible to use an ISP programmer to replace the bootloader code with Optiboot which basically turns it into a UNO with an FTDI USB interface. | ||
| ===== Features | ===== Features | ||
| - | * | + | * Microcontroller: |
| + | * Clock Speed: 16 MHz crystal oscillator | ||
| + | * 14 digital input/ | ||
| + | * 6 analog inputs | ||
| + | * Operating Voltage: 5V | ||
| + | * Input Voltage: 7-12V | ||
| + | * 3.3V Power Out: up to 50 mA | ||
| + | * 5V Power Out: up to | ||
| + | * I/O Pin Out: up to 20 mA | ||
| + | * Digital I/O Pins: 14 (6 support PWM output) | ||
| + | * Analog Input Pins: 6 (with 10-bit resolution) | ||
| + | * Flash Memory: 16 kB (ATmega168) or 32 kB (ATmega328) (2kB used by bootloader) | ||
| + | * SRAM: 1 kB (ATmega168) or 2 kB (ATmega328) | ||
| + | * EEPROM: 512 bytes (ATmega168) or 1 KB (ATmega328) | ||
| + | * Serial I/O: 4 UARTs, one SPI and one I2C interface | ||
| + | * Reset-en jumper, so you can disable auto reset on powerup/USB connection (not on later versions) | ||
| \\ | \\ | ||
| ---- | ---- | ||
| ===== Schematics ===== | ===== Schematics ===== | ||
| + | {{electronic: | ||
| + | {{electronic: | ||
| \\ | \\ | ||
| ---- | ---- | ||
| ===== Examples ===== | ===== Examples ===== | ||
| + | ^Probable Jaycar clone :^ | ||
| {{electronic: | {{electronic: | ||
| + | {{electronic: | ||
| + | {{electronic: | ||
| + | |||
| + | ^Examples from Wikimedia:^ | ||
| {{electronic: | {{electronic: | ||
| + | {{electronic: | ||
| ====== References and Additional Resources ====== | ====== References and Additional Resources ====== | ||
| - | * [[https:// | + | |
| + | | ||
| + | * [[https:// | ||
| + | * {{https:// | ||
| < | < | ||